How to use Audio Volume Booster
- 1Add an audio file, or a video if you want its sound louder as an audio file. The file name, size, length and codec appear once it has been read.
- 2Pick Auto level, or a fixed gain: +3, +6, +9, +12 or +18 dB to make it louder, or -6 dB to make it quieter.
- 3Choose MP3, M4A or WAV. The estimated output size is shown under the options. Click Boost volume.
- 4Listen to the preview, then download. The file is named after the original with -leveled or the gain added, for example memo-plus12dB.mp3.
When a recording needs a boost
Phone voice memos recorded from the far side of a table, a lecture captured from the back row, a Zoom call saved with the microphone set too low, an old cassette transfer: they all end up as files you have to turn the speakers all the way up for. Raising the level once, in the file itself, means it plays at a normal volume on every device and does not blast you when the next track starts.
The same tool also helps when several clips must sit together, such as interview answers for a podcast or tracks for a school presentation. Running each through Auto level brings them to one common loudness, so nobody has to ride the volume knob between them.
Auto level or a fixed gain
Auto level measures the loudness of the whole file and moves it to -16 LUFS, the level podcasts and most streaming services target, with peaks kept under -1.5 dB. A whispered voice memo and a loud music track both come out at the same comfortable level, so it is the right choice when you do not know how much louder you need.
A fixed gain is simpler and predictable: +6 dB is roughly twice as loud, +12 dB four times. Use it when a recording is just a little too quiet or when several files must be raised by the same amount. The -6 dB option goes the other way, for a clip that is uncomfortably loud next to the rest.
Why it does not crackle
Raising a loud recording by 12 dB would push its peaks past the maximum a file can hold, which sounds like crackling. A limiter runs after the gain and gently holds those peaks just below the ceiling, so quiet parts get louder and loud parts stay clean. If a file is already loud, a big boost makes it flatter rather than louder; Auto level is the better tool then.
What happened when we tested it
We used a 20-second mono MP3 at 96 kbps (235 KB) that imitates a quiet voice memo: a mean volume of -38.9 dB, an integrated loudness of -39.7 LUFS and peaks at -29 dB. With +12 dB it came back in about 1.5 seconds at a mean of -26.9 dB and -27.7 LUFS, exactly 12 dB up. With Auto level it measured -16.2 LUFS with peaks at -5.4 dB, right on the podcast target. Both results were 470 KB, twice the original, because the output is written at 192 kbps instead of 96.
We also gave it a 10-second 720p MP4 with an AAC soundtrack and chose +6 dB as M4A. The result was a 160 KB audio file whose mean volume went from -21.1 dB to -14.8 dB, ready in about two seconds. The picture is dropped; only the sound is saved.
What it cannot do
Louder is not the same as clearer. Background hiss, hum and room echo are raised together with the voice, so a noisy recording becomes a loud noisy recording. The tool does not remove noise or isolate speech. It also treats the file as a whole: it cannot raise one quiet speaker in a conversation while leaving the others alone. If a file contains several audio tracks, only the first one is processed.
Common problems
If the tool says the file has no sound track, the video was recorded or exported without audio, and there is nothing to boost. If the result sounds squashed or pumping, the source was already loud and the gain was too high; go back with Change settings and use a smaller step or Auto level. If the output is bigger than the input, that is the 192 kbps encoding at work, and choosing M4A keeps it a little smaller with the same quality.
Formats and privacy
Input can be MP3, M4A, AAC, WAV, OGG, Opus, FLAC, WMA or a video file such as MP4, MOV, WebM or MKV. Output is MP3 at 192 kbps, M4A (AAC at 192 kbps) or lossless 16-bit WAV, and title and artist tags are carried over. Processing runs in your browser with FFmpeg (about 10 MB, downloaded once and then cached) and the file never leaves your device.
Frequently asked questions
How much louder is +6 dB?
About twice as loud to the ear. +12 dB is about four times, +18 dB about eight times.
Can I make a video louder and keep it as a video?
Not yet; this tool saves the sound as an audio file. A louder-video option is planned.
Will boosting reduce quality?
The file is re-encoded once at 192 kbps, which is transparent for speech and fine for music. Choose WAV for a lossless result.
What does -16 LUFS mean?
LUFS is a unit of perceived loudness measured over the whole file, not just the peaks. -16 LUFS is a common target for podcasts and spoken audio, so a file leveled to it sits comfortably next to most shows and playlists.
Should I use Auto level or +12 dB on a voice memo?
Auto level, unless you need several files raised by the same amount. It works out the right gain from the measured loudness, so you do not have to guess.
Can it make one file quieter?
Yes. Choose -6 dB, or use Auto level, which lowers a file that is louder than the target as well as raising a quiet one.